Bike Tools

[DomJBo]

Saving up to go on bike maintenance and repair course. Was wondering what tools are needed. (Campy)

 

 

 

Seen a few tool boxes as such:

 

http://www.chainreactioncycles.com/Models.aspx?ModelID=17700

 

 

 

Are all these tools really neccassary? Or can i get by in the beginning on something like this?

 

http://www.chainreactioncycles.com/Models.aspx?ModelID=29798

[splat]

I think most of the tool boxes are more Shimano oriented (BB tools etc). I see the Park tools one has Campy stuff, so the Shimano stuff is unused = waste of money for you.

 

Rather build up your own with tools you will actually use as you learn.

 

(Also Park products are pretty expensive, you can get better value on other brands). ie you dont need Park screw drivers or shifting spanner etc.

 

I also think you pay duties on tools. Not sure about that though...

[AndreZA]

Buy tools as the job requires.

[Minion]

If you're just working on one type of bike, then consider buying

individual tools as and when you need them. It usually works out cheaper

and spreads the cost out over a longer period than if you buy a box

full of tools you don't need.

 

 

 

A couple of things you could consider getting for basic maintenance and cleaning:

• Allen key set - a must-have. Buy from Builder's Warehouse, Mica etc.

• Cassette/BB tool - Campag uses the same tool for cassettes and pre-UT BBs. Try and get one to fit a metric spanner e.g. Pedros
• Spanner to hold Cassette/BB tool. A shifting spanner would work as a low cost start.

• Chain whip
• Pedal wrench. Depends on the type of pedals e.g. Look pedals use Allen keys so you don't need one. Don't skimp, buy a big one with a long handle.

• Metal ruler with inch markings to measure chain wear.

When it comes time to replace your chain, consider getting a chain tool.

 

When you need to replace cables, look for a good cable cutter e.g. Pro. A fourth hand tool is also pretty useful.

 

If you have to remove or install Campag brakes you'll need a 15mm cone wrench.

 

If you're working on a newer Ultra-torque BB you'll need a tool for that.

 

You may need other cone wrenches to service your wheels.

 

 

 

[Johan Bornman]

Never buy a complete toolbox. The minute you do, you'll discover you need yet another tool and then there's no place to put it in your fancy new recessed toolbox. Consider a tool roll made for cycling.

 

As Edman says, spread the load and buy tools as you need them. For instance, decide you'r going to service your wheels this month. Then buy tools for that and do the research for that job only. Don't overwhelm yourself.

 

Get a good book - Park Blue Book for instance. Much cheaper from CRC than local.

 

Buy a tub of grease - any grease and a tube of copper compound.

 

Don't try and buy one brand only. Buy best best-of-breed and screw the  true-blue approach.

 

I'm biased, so I'll add that you should consider kick-starting your skills by doing a course. Instruction is the mother of confidence.

 

Edit: Oh, I see you are considering a course. Don't buy tools until after the course. There you'll have the opportunity to use several different styles of tools and you can decide what you like and don't.

 

 

 

[stewie911]

Buy tools from Johan. Free marketing and bump.

 

But seriously, Johan Bornman knows his stuff and gives great advice.

 

[MobileBikeTec]

If I can give you my opinion, get the Pedros Briefcase Toolbox, its got EVERYTHING you need in it, and the SHIMANO wooden chain-braker, its my favourite tool in my whole toolbox!

 

If you ever in need of a workshop stand... if you travel with it I'd say Feedback Sports - Ultimate workshop stand!

And if you want a wall mounted one, I've got 2 Park Tool top end wall mount clamps that I want to get rid of (we renting so I cant mount them)

 

And get a cool apron!!!! Snap on tools has got a schweet one that I'm using!

 

Have fun!

[Guest Big H]

If you're just working on one type of bike' date=' then consider buying individual tools as and when you need them. It usually works out cheaper and spreads the cost out over a longer period than if you buy a box full of tools you don't need.

A couple of things you could consider getting for basic maintenance and cleaning:

Allen key set - a must-have. Buy from Builder's Warehouse, Mica etc.

Cassette/BB tool - Campag uses the same tool for cassettes and pre-UT BBs. Try and get one to fit a metric spanner e.g. Pedros

Spanner to hold Cassette/BB tool. A shifting spanner would work as a low cost start.

Chain whip

Pedal wrench. Depends on the type of pedals e.g. Look pedals use Allen keys so you don't need one. Don't skimp, buy a big one with a long handle.

Metal ruler with inch markings to measure chain wear.When it comes time to replace your chain, consider getting a chain tool.

When you need to replace cables, look for a good cable cutter e.g. Pro. A fourth hand tool is also pretty useful.

If you have to remove or install Campag brakes you'll need a 15mm cone wrench.

If you're working on a newer Ultra-torque BB you'll need a tool for that.

You may need other cone wrenches to service your wheels.

[/quote']

Use a syringe to oil derraileur and brake pivot points. Buy a thick needle and remove the sharp end on a piece of wet sandpaper.

Cut a tube into small strips and use as rubber bands. usefull when setting v-brakes.

Keep broken spokes. Grind a piece to a sharp point. Bend the back portion over to form a handle. Use this as a awl and to open brake and derraileur housing after they are cut.

Bend a piece of spoke with two hooks on both sides. use this to join the chain when fitting your link pin.

Do NOT buy a chain guage.... Jay Bee will never ever ever forgive you!!!!!!

Always have at least two rear derraileur cables, two front derraileur cables and two brake cables in stock. They always get stffed on a Saturdaywhen the shops are closed.

Keep some stock like brake pads, a spare chain, appllicable spokes, tubes a tyre etc. The same happens with these on Saturdays when you have a big race on the Sunday.

Buy a refillable grease gun. It is just so much more neater to dump the grease where it is needed.

 

[Johan Bornman]

Bend a piece of spoke with two hooks on both sides. use this to join the chain when fitting your link pin.

 

 

Ek dog dan dis hoe jy biltong hakkies maak.

 

 

Wag net tot jy die nuwe JayBee-approved chain measurement tool sien. Jy sal sommer aan jou biltong stik.

[Guest Big H]

Bend a piece of spoke with two hooks on both sides. use this to join the chain when fitting your link pin.

 

 

Ek dog dan dis hoe jy biltong hakkies maak.

 

 

Wag net tot jy die nuwe JayBee-approved chain measurement tool sien. Jy sal sommer aan jou biltong stik.

 

Boek een vir my. Ek sal inbetaal en hom einde Mei kry. Stuur foto as jy kan ek stuur PM

[didi]

I Think you need one of these babies.

http://www.classicrendezvous.com/Italy/Campagnolo/CampagToolKit/index.html

Cheers

Didi

[Johan Bornman]

Now that is rather nice. It looks expensive.

[Guest Big H]

Ja those sets are unequalled in their completeness and quality. They are also unequalled in their cost and NOT suited for the general DIY tinkerer that owns maybe three bikes at the most.

 

I just like all those reamers in the set.