Stretched@Birth Posted February 10, 2014 Author Posted February 10, 2014 Test fitted on the frame. divernick 1
Stretched@Birth Posted February 10, 2014 Author Posted February 10, 2014 The fork ends have been laser cut out of 4mm plate. Problem is, because the triple clamps are off a motorbike, they are wider than I want. Was looking to cut some plate to build spacers, but this would be a hack. Then remembered, rear axles are wider than fronts, and fit the gap perfectly. So, rear axle in the front hub and all should be peachy. Tomorrow, I weld the fork ends. Sent from my iPad using Tapatalk 2
Bobbo_SA Posted February 10, 2014 Posted February 10, 2014 On 2/10/2014 at 6:49 AM, Stretched@Birth said: Test fitted on the frame. Multi-purpose boat anchor? Looking good, going to be sick, will get side inserts done ASAP
Stretched@Birth Posted February 10, 2014 Author Posted February 10, 2014 On 2/10/2014 at 5:54 PM, Bobbo_SA said: Multi-purpose boat anchor? Looking good, going to be sick, will get side inserts done ASAP Not something you'll be riding around on the back wheel no, that front end is heavy! Sent from my iPad using Tapatalk 2
Bobbo_SA Posted February 10, 2014 Posted February 10, 2014 On 2/6/2014 at 8:09 AM, Stretched@Birth said: Ok, maybe I should just put out a wanted ad for a black square taper crankset... Sent from my iPad using Tapatalk 2 Square taper should be fine to anodize, no shaft to dissolve
Stretched@Birth Posted February 10, 2014 Author Posted February 10, 2014 On 2/10/2014 at 6:35 PM, Flippa said: How about an isis crank? Is it black? Sent from my iPad using Tapatalk 2
Stretched@Birth Posted February 10, 2014 Author Posted February 10, 2014 (edited) Edit: double post Edited February 10, 2014 by Stretched@Birth
Flippa Posted February 10, 2014 Posted February 10, 2014 On 2/10/2014 at 6:55 PM, Stretched@Birth said: Is it black? Sent from my iPad using Tapatalk 2 Ya
Stretched@Birth Posted February 10, 2014 Author Posted February 10, 2014 On 2/10/2014 at 6:57 PM, Flippa said: Ya Will have to bring beer, check out your build and raid your parts bin! Sent from my iPad using Tapatalk 2
Flippa Posted February 10, 2014 Posted February 10, 2014 On 2/10/2014 at 6:59 PM, Stretched@Birth said: Will have to bring beer, check out your build and raid your parts bin! Sent from my iPad using Tapatalk 2 Sure. Just give me a shout.
Stretched@Birth Posted February 18, 2014 Author Posted February 18, 2014 Fork-ends welded, still a small bit of fabrication to do, and then paint! Flippa 1
Stretched@Birth Posted February 20, 2014 Author Posted February 20, 2014 It rolls! Happy to report that everything on the fork lines up, wheel is centered and straight, need to chop the legs a little shorter. NotSoBigBen, ewep and the nerd 3
Flippa Posted February 20, 2014 Posted February 20, 2014 Why do you want to shorten the legs? thought you were going with the raked out look?
Stretched@Birth Posted February 20, 2014 Author Posted February 20, 2014 On 2/20/2014 at 4:59 AM, Flippa said: Why do you want to shorten the legs? thought you were going with the raked out look?Nope, board racer look. The stance is right at the moment, need to just trim the tops off where they're protruding through the top clamp.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now