Ti-ny Posted February 18, 2017 Share So decided to upgrade road bike crank to hollow tech. Trying to remove old octalink crank and I have managed to lose the little bobbit at the front of my crank puller. Is there a way to remove the crank without it or does someone in Durbanville have a crank puller I could use please. Sent from my HUAWEI GRA-L09 using Tapatalk Link to comment Share on other sites More sharing options...
BaGearA Posted February 18, 2017 Share If you don't car about the old crank you could just take a drift and hammer the thing off , tap a spot move over diagonally tap move to other corner tap diagonally over again and repeat. ONLy if you're going to throw the crank away cause this fuc*s up the crank pretty good Link to comment Share on other sites More sharing options...
Vetseun Posted February 18, 2017 Share If you were in Bloem l, I could have helped. Ti-ny 1 Link to comment Share on other sites More sharing options...
Ti-ny Posted February 18, 2017 Share Thanks crank still good but im not going to use it so will try hammer just worried about stress on frame Sent from my HUAWEI GRA-L09 using Tapatalk Link to comment Share on other sites More sharing options...
shaper Posted February 18, 2017 Share Use a bolt nut of small enough size as a replacement bobbit, then the nut can be against the axle and you should have enough when you screw the bolt up against the nut to pull the crank off Edited February 18, 2017 by shaper Ti-ny and johannrissik 2 Link to comment Share on other sites More sharing options...
Ti-ny Posted February 18, 2017 Share Cool sounds like it could work thanks Sent from my HUAWEI GRA-L09 using Tapatalk Jaws677 1 Link to comment Share on other sites More sharing options...
BaGearA Posted February 18, 2017 Share Use a bolt nut of small enough size as a replacement bobbit, then the nut can be against the axle and you should have enough when you screw the bolt up against the nut to pull the crank offLearn something new everyday Link to comment Share on other sites More sharing options...
shaper Posted February 18, 2017 Share Learn something new everyday It works, had an issue once where the bobbit head was too big to fit in the axle hole. Found a bolt head that would fit, removed the bobbit, screwed in the crank removal tool, then tightened the bolt against the nut resting against the axle and pulled the crank off Edited February 18, 2017 by shaper Link to comment Share on other sites More sharing options...
Ti-ny Posted February 18, 2017 Share Ok size is the same as 10c coin will go to builders tom to find right size nut Sent from my HUAWEI GRA-L09 using Tapatalk johannrissik 1 Link to comment Share on other sites More sharing options...
shaper Posted February 18, 2017 Share Ok size is the same as 10c coin will go to builders tom to find right size nutSent from my HUAWEI GRA-L09 using TapatalkStack of 10c coins will also work. Just make sure the nut hole is smaller than the crank pull bolt as you do not want it going straight through, as you want the crank puller bolt to push against the nut, stack of washers, stack of 10c coins which is pushing on the axle johannrissik and Ti-ny 2 Link to comment Share on other sites More sharing options...
steveO:K Posted February 18, 2017 Share Send me a pm with your number. I can help you tomorrow. I'm in Aurora. Ti-ny 1 Link to comment Share on other sites More sharing options...
Ti-ny Posted February 19, 2017 Share Thanks all used a 10mm steel washers sandwiched between two 10c coins. Worked great. Coins and washers bent but cranks came off. Sent from my HUAWEI GRA-L09 using Tapatalk shaper 1 Link to comment Share on other sites More sharing options...
Ti-ny Posted February 19, 2017 Share Send me a pm with your number. I can help you tomorrow. I'm in Aurora.Thanks Steve. Managed to get it sorted Sent from my HUAWEI GRA-L09 using Tapatalk Link to comment Share on other sites More sharing options...
shaper Posted February 19, 2017 Share Thanks all used a 10mm steel washers sandwiched between two 10c coins. Worked great. Coins and washers bent but cranks came off.Sent from my HUAWEI GRA-L09 using TapatalkCool you got it sorted, better than hamering, bashing and cutting the bb to get it off Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now