Drilling and screwing carbon

[T-Bob]

Reckon I'll just get rid of the k-edge and the alpero one's I have and get this. Probably easier in the long run.

 

http://www.shapeways.com/model/973993/racebone-garmin-handlebar-mount.html?li=shop-results&materialId=6

 

http://images1.sw-cdn.net/model/picture/674x501_973993_1159139_1374692319.jpg

[gummibear]

These are cool but need bolts at the end of the stem.

 

http://i1270.photobucket.com/albums/jj620/MultiSports-Forum/Garmin%20Edge%20custom%20mount/GarminMount-Prototype3-001.jpg

 

http://i1270.photobucket.com/albums/jj620/MultiSports-Forum/Garmin%20Edge%20custom%20mount/GarminMount-Prototype3-002.jpg

 

http://i1270.photobucket.com/albums/jj620/MultiSports-Forum/Garmin%20Edge%20custom%20mount/GarminMount-Prototype3-003.jpg

 

http://i1270.photobucket.com/albums/jj620/MultiSports-Forum/Garmin%20Edge%20custom%20mount/GarminMount-Prototype3-004.jpg

[T-Bob]

These are cool but need bolts at the end of the stem.

 

That is exactly what I was sketching up. Who and where?

[VicanZA]

Sounds like u screwed..

[Weight Weenie]

Thinking of one that acts as a spacer and then the mount is attached to that and extends under the bars to the front to mount the gps. Not sure if that would ever work?

[T-Bob]

Thinking of one that acts as a spacer and then the mount is attached to that and extends under the bars to the front to mount the gps. Not sure if that would ever work?

 

That is an option. There are a few that sit on the top to place it out over the top of the stem. I'm guessing the issue there is the distance to get it past the stem vs rise and stiffness / weight.

 

Edited December 12, 2013 by hellocolour

[T-Bob]

Found this on Ebay. Goes between the faceplate. not exactly pretty.

 

http://i.ebayimg.com/00/s/MTIwMFgxNjAw/$(KGrHqNHJBsFCEWGORp(BQhs9LgTDw~~60_35.JPG?set_id=880000500F

Edited December 12, 2013 by hellocolour

[gummibear]

That is exactly what I was sketching up. Who and where?

 

Lost the link.

Will look tomorrow.

[GhostSixFour]

ah... Any one got a 3d printer handy?

 

Might be able to help you there..

[gummibear]

http://weightweenies.starbike.com/forum/viewtopic.php?f=3&t=28122&start=165

[Gandalf]

Can you post a pic of your bars? Then we will make solution

[V12man]

I saw this one the other day - replaces the headset top cap - just scroll down the page a bit to see it.

 

http://www.momsenbikes.com/momsendesign

[T-Bob]

Can you post a pic of your bars? Then we will make solution

 

Will do, out on the road today but will be back in the office this arvo. Cheers for the help in advance!

 

Might be able to help you there..

 

Legendary. thanks for the PM will get back to you on the offer.

[Guest Latent Blue]

http://i.imgur.com/IfOkiSo.gif

 

 

All this talk about drilling and screwing!!!

[arendoog]

Pratley epoxy if you realy want to make it permanent

[Cippo]

 

 

That is an option. There are a few that sit on the top to place it out over the top of the stem. I'm guessing the issue there is the distance to get it past the stem vs rise and stiffness / weight.

 

 

This might be your best option, the one with the adjustable bolt to change angle above your stem.

Edited December 13, 2013 by Cippo