JScottP Posted September 12, 2018 Share Long story short, went for a ride on Saturday and received a lovely large blister in my rear tyre, but fortunately have a spare suagaro tyre in the garage. So remove old tyre, clean rim with soapy water and install new sealant and tyre. Start pumping and wheel won’t stay inflated at all. Turns out the air is leaking out hard from the small air vent in the side of the rim and have no idea why. Rim is an Easton XC70, please help!!! Link to comment Share on other sites More sharing options...
DieselnDust Posted September 12, 2018 Share Tape up the rim bed with gorilla tape Link to comment Share on other sites More sharing options...
TheJ Posted September 12, 2018 Share Air vent on the inside of the rim? Huh? Doesn't sound like your rimtape was put in properly. I use the R25 rolls of silver rimtape you get at some shops. 1 layer. Sometimes, one layer of insulation tape before it, but usually just one layer of cheapy rimtape. https://www.sportsmanswarehouse.co.za/product/sportsmans-warehouse-tubeless-rim-tape Link to comment Share on other sites More sharing options...
fanievb Posted September 12, 2018 Share air vent?pic would be nice Link to comment Share on other sites More sharing options...
fanievb Posted September 12, 2018 Share Tape up the rim bed with gorilla tape Air vent on the inside of the rim? Huh? Doesn't sound like your rimtape was put in properly. I use the R25 rolls of silver rimtape you get at some shops. 1 layer. Sometimes, one layer of insulation tape before it, but usually just one layer of cheapy rimtape. https://www.sportsmanswarehouse.co.za/product/sportsmans-warehouse-tubeless-rim-tape looks like (google) rim is tubeless so no need for rimtape, but I could be wrong Link to comment Share on other sites More sharing options...
BikeisLife Posted September 12, 2018 Share Time for some new tubeless tape. Link to comment Share on other sites More sharing options...
TheJ Posted September 12, 2018 Share looks like (google) rim is tubeless so no need for rimtape, but I could be wrong Agree, does look like no tape needed. So by airvent he could only mean the valve hole. Maybe the valve isn't snugging up tight enough on the inside of the rim. Could remedy that by cranking the locknut a bit more, but sometimes that might not work. Depending on the actual tubeless valve, if the rubber bit was round, I'd drill the rim out ever so slightly so that the valve can "pull into" the rim a tiny bit. Locking it down with the lockring would then be pretty airtight. If the value had a square rubber bit... hmmmm... DieselnDust and fanievb 2 Link to comment Share on other sites More sharing options...
JScottP Posted September 12, 2018 Share Agree, does look like no tape needed. So by airvent he could only mean the valve hole. Maybe the valve isn't snugging up tight enough on the inside of the rim. Could remedy that by cranking the locknut a bit more, but sometimes that might not work. Depending on the actual tubeless valve, if the rubber bit was round, I'd drill the rim out ever so slightly so that the valve can "pull into" the rim a tiny bit. Locking it down with the lockring would then be pretty airtight. If the value had a square rubber bit... hmmmm... Hit the nail on the head! Turns out when I added a new valve as well it wasn’t quite sitting flush in the rim bed allowing air to get through the valve hole and under the welded rim bed and escaping out the vent. When I say vent, there is a tiny hole on the outside of either side of the rim that is apparently drilled when they weld the rim allowing the hot air to escape from the welding. Link to comment Share on other sites More sharing options...
Thomo Posted September 12, 2018 Share air vent? pic would be niceMore like a water drainage hole.? Usually fixed by re-taping.Existing tape likely leaking. Edited September 12, 2018 by Thomo Link to comment Share on other sites More sharing options...
TheJ Posted September 12, 2018 Share When I say vent, there is a tiny hole on the outside of either side of the rim that is apparently drilled when they weld the rim allowing the hot air to escape from the welding. Well that's just stupid then... How can they make a "tubeless" rim... and then leave it with a hole in. Eish. Link to comment Share on other sites More sharing options...
nick_the_wheelbuilder Posted September 12, 2018 Share Yes, many rims have a small hole in the external wall of the rim. I can only assume this is to compensate for air pressure changes or to drain any water from the rim that may find it's way in there..... A proper taping inside the rim is normally all that's needed for good tubeless performance, as long as tubeless-ready rims and tyres are used. Edited September 12, 2018 by nick_the_wheelbuilder DieselnDust 1 Link to comment Share on other sites More sharing options...
Shebeen Posted September 12, 2018 Share Am I reading this right, tubeless rims don't need tape?How do you stop the air getting out the spoke holes? Or am i the confused one. the only thing a tubeless wheel helps you with is not required the black conversion strips. Ger Oos 1 Link to comment Share on other sites More sharing options...
Kranswurm Posted September 12, 2018 Share Am I reading this right, tubeless rims don't need tape?How do you stop the air getting out the spoke holes? Or am i the confused one. the only thing a tubeless wheel helps you with is not required the black conversion strips.If its got spoke holes it obviously is not tubeless DieselnDust 1 Link to comment Share on other sites More sharing options...
droo Posted September 13, 2018 Share The hole is a vent to release gases during welding. You'll find them on chainstays and seatstays on alu and steel frames too. The more you know... Wannabe and DieselnDust 2 Link to comment Share on other sites More sharing options...
Andreas_187 Posted September 13, 2018 Share If its got spoke holes it obviously is not tubelessNot true. Rim tape seals spoke holes. A tubeless rim has a specific edge on the inside rim to hold the tubeless tyre securely. Link to comment Share on other sites More sharing options...
DieselnDust Posted September 13, 2018 Share Not true. Rim tape seals spoke holes. A tubeless rim has a specific edge on the inside rim to hold the tubeless tyre securely. Kransie is right. The rim bead is only a secondary consideration. A proper tubeless rim has a continuous sealed spoke bed that does not require taping to close off the spoke holes Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now