ChrisF Posted May 7, 2023 Share Lesson for the day .... Murphey is a "naughty man" .... Did the once over check before leaving home. Actually did a short ride outside the house checking the tyre pressures before closing the garage. 3km later the bike feels "weird" .... cant put my finger on it, but something is off. As I go past CWC on the way to the trails I check the handling again, certainly something off .... checking to the back .... rear tire lost pressure before the Sludge sealed a puncture. I have one of those mini pumps ..... maar wie wil nou reg op n fiets winkel se stoep sukkel .... Thanks to the guys at CWC. Quickly topped up the pressure, and off I went. 30km further, no issues. Murphey oooooo murphey ....... jou bliksem. KB280DT and Scary Rider 2 Link to comment Share on other sites More sharing options...
Chadvdw67 Posted May 12, 2023 Share Dont put your hands near the spinny rotatey thingies absent mindedly while they are spinny spinning...... Frosty, splat, devvydoesdonuts and 9 others 1 1 10 Link to comment Share on other sites More sharing options...
thebob Posted May 12, 2023 Share On 4/17/2023 at 1:53 PM, Frosty said: Anyway, sanity prevailed and a short while later I was done. New chain days are awesome. That story reminds me of 3 hour struggle with a chain I had with a KTM 250 the day before a race. That horrible episode is why I have a rule which is to never work on a bike the day before a race besides lubing the chain and checking the tyre pressure love2fly and ChrisF 1 1 Link to comment Share on other sites More sharing options...
MrJacques Posted May 12, 2023 Share 1 hour ago, thebob said: That story reminds me of 3 hour struggle with a chain I had with a KTM 250 the day before a race. That horrible episode is why I have a rule which is to never work on a bike the day before a race besides lubing the chain and checking the tyre pressure Yup! Been there done that and managed to push the brake piston out while checking the brakes with the wheel off. Had to borrow a brake from someone who fortunately had a spare for me. I don't think I had the supplies to bleed it myself yet. Link to comment Share on other sites More sharing options...
Kingston coetzee Posted May 12, 2023 Share Literally today I tried to fix my tektro disk brake and ended up with no brakes at all🤦🏻♂️ ChrisF and Mtree 1 1 Link to comment Share on other sites More sharing options...
MrJacques Posted May 13, 2023 Share 9 hours ago, Kingston coetzee said: Literally today I tried to fix my tektro disk brake and ended up with no brakes at all🤦🏻♂️ Brakes can be tricky. Not sure what happened to yours, but bleeding incompletely can leave bubbles and a spongy feeling. Pulling the lever with nothing to stop them can pop the pistons out. Getting oil on the pads and rotors can lead to brakes that don't work well. Rotors can be cleaned. Pads not really, unless they're sintered. If you're lucky a bit of light sandpapering and then bedding in may work. I've tried soaking resin pads in alcohol and heating them up which worked for a short while, until they disintegrated on the trail. I think one or both of those up messed up the resin. Also not installing the pin / bolt can lead to them falling out on the trails. Something that did seem to work for getting some bubbles out was to open the reservoir and tape up the lever in a squeezed position and leave it like that overnight. Then top up. Zebra 1 Link to comment Share on other sites More sharing options...
The Ouzo Posted May 13, 2023 Share 13 hours ago, Chadvdw67 said: Dont put your hands near the spinny rotatey thingies absent mindedly while they are spinny spinning...... sheez, howz about a warning first. That look eina. and its in one of those places that just makes healing a bastard. Link to comment Share on other sites More sharing options...
Chadvdw67 Posted May 13, 2023 Share 1 hour ago, The Ouzo said: sheez, howz about a warning first. That look eina. and its in one of those places that just makes healing a bastard. And I work with my hands in a factory everyday, going to be a rough couple days up ahead ChrisF, TheoG and Mtree 3 Link to comment Share on other sites More sharing options...
TheoG Posted May 14, 2023 Share On 5/12/2023 at 7:03 PM, Chadvdw67 said: Dont put your hands near the spinny rotatey thingies absent mindedly while they are spinny spinning...... Also made that mistake a few years ago, caught my thumb, took for ever to grow the nail back ... 🙈 Link to comment Share on other sites More sharing options...
MrJacques Posted May 14, 2023 Share You need a decent properly fitting 2mm hex / allen key for Shimano brake lever bleed caps. You need to insert it properly (may need to tap it in) or you're like to round off the hole (I alsmost did) and then you'll have to make other plans to get that cap off. Link to comment Share on other sites More sharing options...
Frosty Posted May 14, 2023 Share 44 minutes ago, MrJacques said: You need a decent properly fitting 2mm hex / allen key for Shimano brake lever bleed caps. You need to insert it properly (may need to tap it in) or you're like to round off the hole (I alsmost did) and then you'll have to make other plans to get that cap off. A rounded bolt and be removed by placing an elastic rubber band in first, then the Allen key, so the elastic is on 4 sides of the hex. Not sure on 2mm, as it’s a bit small, but it works well on 4mm and bigger; also on screw driver heads too. But I guess “how tight” is another thing causing rounded problems. Scary Rider 1 Link to comment Share on other sites More sharing options...
MrJacques Posted May 14, 2023 Share 1 minute ago, Frosty said: A rounded bolt and be removed by placing an elastic rubber band in first, then the Allen key, so the elastic is on 4 sides of the hex. Not sure on 2mm, as it’s a bit small, but it works well on 4mm and bigger; also on screw driver heads too. But I guess “how tight” is another thing causing rounded problems. I've tried the rubber band trick on a rounded out top cap bolt and it didn't work for me, but I also didn't have it on 4 sides. It was a 'fancy' top cap with holes, so I could at least use pliers to undo the cap. Frosty 1 Link to comment Share on other sites More sharing options...
W@nted Posted May 14, 2023 Share So I managed to fix a slipping seatpost (aluminium post in carbon frame). Tried carbon friction paste, no success using the indicated torque values on the clamp… Then tried the old chalk trick. Works a charm! Basically applied chalk on the clamp area. No slippage. I am however not sure what the long term effect can be on the alu/carbon? dasilvarsa 1 Link to comment Share on other sites More sharing options...
MrJacques Posted May 14, 2023 Share 51 minutes ago, W@nted said: So I managed to fix a slipping seatpost (aluminium post in carbon frame). Tried carbon friction paste, no success using the indicated torque values on the clamp… Then tried the old chalk trick. Works a charm! Basically applied chalk on the clamp area. No slippage. I am however not sure what the long term effect can be on the alu/carbon? Never heard of the chalk trick, will keep that in mind. I think you're risking galvanic corrosion and a stuck seatpost: Can You Put a Carbon Seat Post In an Aluminum Frame? – Brainy Biker Link to comment Share on other sites More sharing options...
MrJacques Posted May 14, 2023 Share First time I've seen these clips on a bike. They're meant to stop the bolts backing out. TheoG 1 Link to comment Share on other sites More sharing options...
RobertWhitehead Posted May 14, 2023 Share 3 hours ago, Frosty said: A rounded bolt and be removed by placing an elastic rubber band in first, then the Allen key, so the elastic is on 4 sides of the hex. Not sure on 2mm, as it’s a bit small, but it works well on 4mm and bigger; also on screw driver heads too. But I guess “how tight” is another thing causing rounded problems. You know what I use? I've always wanted one and finally got one for a steal: I use a Dremel to cut a groove on any rounded bolt head then simply use a flat 😁. I then chuck the bolt and replace it with a new one Frosty, dasilvarsa, Mtree and 2 others 5 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now