What have you 3D printed for your bike?

[BaGearA]

I need 5 X2 or 2 piston caliper spacers please 

 

Beer or cupcakes or jus cold had cash on offer 

[Jono]

On 8/17/2022 at 3:18 PM, BaGearA said:

I need 5 X2 or 2 piston caliper spacers please 

 

Beer or cupcakes or jus cold had cash on offer 

Pretty cool of Hope to make these available. I’ll happily print them, but I’m in Cape Town. Send me a dm if you don’t come right locally 

[splat]

On 7/20/2022 at 8:14 AM, splat said:

I would love a saddle rail mount for a Bontrager Flare tail light

It's so much neater than the rubber strap mount on the seat post.

I collected it yesterday, but haven't had a chance to fiddle with it yet.
The edges are rough, so may need a bit of sanding down for the light to slide on and off easily.

[Sprockets]

I got myself a printer the other day. Going to try experiment printing a set of these and see how it goes! Just need to draw it up first ... 😬

 

[ChrisF]

With my Garmin 520 showing it age and needing a battery bank for longer rides I have been looking all over for a bracket ....

 

Francois was kind enough to print this -

 

Different radia as per the bar and the battery bank, with allowance for a thin foam layer

 

 

 

3mm self adhesive foam to protect the bar and some 50mm velcro ...

 

 

Edited September 1, 2022 by ChrisF

[Steady Spin]

Anyone in Gauteng that is a wizard at scanning and printing a small cable guide for me? 

Bike came without a dropper post compatible plate and it would be great if I didn't have to drill out the existing one. 

It is the one in the middle. Will need some custom design work.

[Frosty]

Asked a friend to print me this, after discovering I have two sets of pedals that have too much play.

[NotSoBigBen]

1 hour ago, Frosty said:

Asked a friend to print me this, after discovering I have two sets of pedals that have too much play.

Probably one of the most popular items I print for mates and family!

[ChrisF]

2 hours ago, Frosty said:

Asked a friend to print me this, after discovering I have two sets of pedals that have too much play.

Uhm ....

 

Please tell more ....

 

 

How is this used to reduce the play ?

[NotSoBigBen]

47 minutes ago, ChrisF said:

Uhm ....

 

Please tell more ....

 

 

How is this used to reduce the play ?

https://www.parktool.com/en-int/blog/repair-help/spd-pedal-overhaul

[PhilipV]

12 hours ago, ChrisF said:

Uhm ....

 

Please tell more ....

 

 

How is this used to reduce the play ?

It's a shimano pedal tool. Use it to open your pedals, adjust the bearings with spanners, and then close it again with this tool. 

[Hairy]

37 minutes ago, PhilipV said:

It's a shimano pedal tool. Use it to open your pedals, adjust the bearings with spanners, and then close it again with this tool. 

And then your Shimano pedals are ready to rock for the next 45 years before a service is required!

[Frosty]

20 hours ago, ChrisF said:

Uhm ....

Please tell more ....

How is this used to reduce the play ?

Those that know me, will know I ride with the same gear for years.
My 105 spd-SL pedals have done about 80,000Km without being serviced; but they certainly need it now. 4x new bearings.

 

http://1.bp.blogspot.com/-mYFYaub4AMo/UClivFSEaJI/AAAAAAAABUk/ilgW83vKw4s/s1600/spdexplshim.jpg

Edited October 12, 2022 by Frosty

[JB77]

Does anyone on this thread want to potentially print me a garmin mount for aero extensions? Please personal message me, thanks.

[Steven Knoetze (sk27)]

On 8/23/2022 at 6:17 PM, splat said:

I collected it yesterday, but haven't had a chance to fiddle with it yet.
The edges are rough, so may need a bit of sanding down for the light to slide on and off easily.

Check this out.

Very cool.

[Headshot]

I need a chain slider for an old adventure moto I am restoring. Has anyone had such a thing printed or know a company which might be able to assist?